Offline
Cleveland, OH
nitro2k01 wrote:

I'll have to try the extra cap on the voltage rail to see if it gets rid of the horrible buzz.

It works wonders. Kills almost all of the hum. Even to the headphone jack.

Offline
CA
katsumbhong wrote:

1. They aren't polarized. Check your prescription.
2. For the non-polarized.

I see now, my bad. Prescription says cocaine so that could be the reason I saw polarized...

Offline
Taichung, Taiwan
nitro2k01 wrote:

I recently touched up the prosound my old GBC that I've used for experiments. I'm tapping the signals off the same point (basically right off the CPU pins). But I've done away with the caps and just placed resistors in series, about 100 ohm or so. This DC couples the signal completely for the flattest possible frequency response. This relies on the receiving equipment having DC blocking caps, which is almost always the case.

Whether or not you put the cap in series, I recommend putting a resistor in series as well as a protection against a short circuit to ground or an output to output connection. With just the cap in series, there is a dead short to the other side for frequencies above DC (0 Hz) which may damage the CPU if an incorrect connection is made.

You can use a polarized capacitor for the signal coupling if you put the + side toward the CPU. The CPU will always produce frequencies between 0 and +5V, so the polarity requirement should not be violated.

I'll have to try the extra cap on the voltage rail to see if it gets rid of the horrible buzz.

Paging ThursdayCustoms.

You think it's possible to make a small-form factor pcb with said components as a gbc bass mod pcb?

Offline
matt's mind

haha, starting fooling around looking for parts (and making footprints) on this a little earlier today tongue  great minds!  also, i sorely miss eagle lately hmm

i wish we had an @ feature on this site,

like, @thursdaycustoms

that'd be nice. 

@thursdaycustoms !!!

Offline
Sweeeeeeden

Why would you need a PCB for this? It actually seems far easier to have the components hanging in free air for this one.

Offline
Taichung, Taiwan
nitro2k01 wrote:

Why would you need a PCB for this? It actually seems far easier to have the components hanging in free air for this one.

I was thinking a small, in-line, thin, rectangular pcb with smd components. One pcb for each channel so that they can be made in bulk. If I can get ito it soon, I'll see about doing a quick drawing and post it up.

What I imagine is a pcb similar in size to the low-battery led pcbs that kitsch sells.

*edit*

There reason why I am thinking about pcbs versus the free hanging bits is for this mod to be available to people who don't have the best soldering skills in the world. The way I did it is fairly involved and takes a bit of time and patience. A PCB would save time and the end user would only have to solder 4 wires at most.

I would, myself, directly replace the smd components on the pcb of the gbc but I don't have the proper tools to work with smd components.

Last edited by katsumbhong (Jul 2, 2014 6:12 pm)

Offline
Cleveland, OH

I have actually thought of doing this. The main problem is that I have not been able to find a 470uf capacitor as small as I would like. Could only find size D or E. Kitsch has this now though: http://store.kitsch-bent.com/product/gbamp

Offline
Alive and well in fucksville
thursdaycustoms wrote:

I have actually thought of doing this. The main problem is that I have not been able to find a 470uf capacitor as small as I would like. Could only find size D or E. Kitsch has this now though: http://store.kitsch-bent.com/product/gbamp

does this contraption change the line signal in any way?

Offline
Taichung, Taiwan
thursdaycustoms wrote:

I have actually thought of doing this. The main problem is that I have not been able to find a 470uf capacitor as small as I would like. Could only find size D or E. Kitsch has this now though: http://store.kitsch-bent.com/product/gbamp

The 470uf cap would be something separate though. I was referring to the bass mod part...

Offline
Taichung, Taiwan
bitjacker wrote:
thursdaycustoms wrote:

I have actually thought of doing this. The main problem is that I have not been able to find a 470uf capacitor as small as I would like. Could only find size D or E. Kitsch has this now though: http://store.kitsch-bent.com/product/gbamp

does this contraption change the line signal in any way?

This is a question you should post in Kitsch's thread.

Offline

Lots of very helpful info here thank you. Im assuming a post-pot prosound mod would have to be kept separate from the bass mod then?

Offline
New York City

Can you do the noise mod to a DMG? If so, where should I solder the 470uF capacitor?
I have a prosound modification on it already.

Last edited by akira^8GB (Oct 7, 2016 9:25 pm)

Offline
Taichung, Taiwan
akira^8GB wrote:

Can you do the noise mod to a DMG? If so, where should I solder the 470uF capacitor?
I have a prosound modification on it already.

http://chipmusic.org/forums/topic/3805/dmg-bass-mod/

Last edited by katsumbhong (Nov 27, 2016 12:40 am)

Offline
Naptown

oh no, are all the photos really down? sad

Offline
Taichung, Taiwan
urbster1 wrote:

oh no, are all the photos really down? sad

They work fine for me. You're not able to see them?

Offline
Naptown

edit: links aren't working on the forum, but pics are still up here
http://s19.photobucket.com/user/Guild_o … amp;page=1

Last edited by urbster1 (Sep 16, 2017 1:24 pm)