2 Sep 24, 2015 12:01 pm
Re: Customized gear thread (1,206 replies, posted in Nintendo Handhelds)
Jazzmarazz wrote:There is an internal voltage regulator board which increases the voltage output to +5v and something like -20v. Nothing runs on the battery voltage alone.
How fast does that drain the batteries?
Honestly the batteries don't seem to drain much faster but my main issue is the noise the kit creates. There's a loud nonstop hum/buzz that actually became annoying enough for me to not even use this anymore. I just use my other MGB with a regular backlight now. Except for recording I use a DMG.
3 Aug 9, 2015 1:36 pm
Re: The Rarest Game Boy In Existence* (35 replies, posted in Trading Post)
Anyone who ends up with this may want to sterilize the unit and/or wear gloves based on that last picture.
4 May 1, 2015 12:09 pm
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
I thought I mentioned they'd include cart cases? Oh well. You're welcome!
5 Apr 21, 2015 9:59 pm
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
Drag'n'Derp carts are gone. Everything else still available.
6 Apr 20, 2015 1:53 pm
Re: Best wire type for modding DMG (17 replies, posted in Nintendo Handhelds)
I use ribbon cable ripped from old computers.
7 Apr 17, 2015 2:01 pm
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
The carts are pending. I've literally had a dozen offers but I have to go in order.
8 Apr 16, 2015 2:34 pm
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
hi are the
snes consoles still available ?
Yes they are.
9 Apr 15, 2015 7:26 am
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
onapokoya wrote:Is what correct?
Ok, now it is correct. For several hours before I left for work, it was NOT a photo of the back side. Kinda wish I did a screen cap for sanity.
Gotcha. That's strange.
10 Apr 14, 2015 5:45 pm
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
11 Apr 14, 2015 1:19 am
Re: FOR SALE!! D'n'D carts, DMG shells, etc. (55 replies, posted in Trading Post)
Bump because new stuff listed!
12 Sep 4, 2014 2:01 am
Re: Customized gear thread (1,206 replies, posted in Nintendo Handhelds)
Ha! I had a couple dozen original DMG buttons sets and a couple dozen aftermarket DMG button sets sitting around on my work table and my wife grabbed them and did this earring/necklace set combo with them and put them on etsy and they all sold within 2 weeks. She hasn't done more though.
13 Sep 4, 2014 1:52 am
Re: Question about overclocking NES (front loader) (12 replies, posted in Nintendo Consoles)
You would risk breaking the pin off the IC; you'd have to do allot of bending to pull just one pin. If you'er dead set on not cutting a trace, I would de-solder the whole chip and then bend the pin.
With cutting a trace it's a simple job to restore it; the solder mask is very easy to scratch off. I've repaired cracked PCBs, bridging all the broken traces and epoxying the crack on the board. I had a monitor that lasted 10yrs after I rescued it
Yogi
This is what I was thinking would happen as well but I just didn't get it out right. I bivert DMGs and I just cut the traces. If removing single pins was required I wouldn't bother. I think that would be too much work and too risky. Also recently added some link ports to a few Super Gameboys and I just cut the required traces. I never even considered removing a whole pin. It would probably just break the pin off while trying to remove it.
14 Sep 3, 2014 12:11 pm
Re: Question about overclocking NES (front loader) (12 replies, posted in Nintendo Consoles)
Wouldn't pulling the pin be just as "irreversible" as cutting the trace? I'd think just cutting the trace would be easier 'cause if you want to revert it back to stock then you just jump a bit of solder across the cut trace.
15 Jul 14, 2014 4:37 pm
Re: Where to buy triwing screws (7 replies, posted in Nintendo Handhelds)
I'm going on paternity leave soon too! New breed of chip artists are on the rise!
16 Apr 29, 2014 6:05 pm
Re: Thousands of copies of "ET: the Extraterrestrial" found in New Mexico (19 replies, posted in General Discussion)
onapokoya wrote:Though they buried a large lot of the games, I thought these were still readily available for cheap? I have a copy and always assumed that anyone with an Atari had one.
Oh, yes, the game itself is very easy to find. I meant that I would specifically like to have one of the ones that was unearthed at the landfill.
Oh yea gotcha! I wonder how many will include boxes and all that. The article also mentioned of Atari equipment being there as well. I wonder exactly what equipment that was and the condition it was in. They should definitely auction that stuff off.